How to leverage trade data in negotiations

List of contents of this article:

• 1, What are tn system and IT system?
• 2, IT What does the system refer to
• 3, i The t system belongs to
• 4, it system can be applied to which of the following places
• 5, Globalized What requirements should the it system take into account
• 6、What is IT_What is it system

What are tn system and IT system?

1. The it system is a system in which the neutral point of the power supply is not grounded and the exposed conductive part of the electrical equipment is directly grounded; the tt system is a system in which the neutral point of the power supply and the exposed conductive part of the electrical equipment are directly grounded; the tn system is the neutral point of the power supply is directly grounded and the conductive part of the electrical equipment is exposed. A system that is directly electrically connected to the neutral point of the power supply.

2. The second capital letter T indicates that the shell of electrical equipment is directly grounded, but it is not connected to the grounding system of the power grid;N indicates that the shell of the electrical equipment is connected to the grounding neutral wire of the system. TN system: the neutral point of the power transformer is grounded, and the exposed part of the equipment is connected to the neutral wire. TT system: neutral point grounding of the power transformer, and the protective grounding of the electrical equipment shell.

3. The IT system is the international standard IEC60364 that distinguishes three different types of grounding systems, and uses two letter codes to represent TN, TT and IT. The first letter indicates the relationship between the power supply end and the ground: T indicates that the power supply end is a little directly grounded; I means that all the charged parts of the power supply end are not grounded or a little grounded by impedance.

4. The TN system is a system in which the neutral point of the power supply is directly grounded, and the exposed conductive part of the equipment is directly electrically connected to the neutral point of the power supply. In the TN system, all electricalThe exposed conductive parts of the equipment are connected to the protection line and connected to the connection point of the power supply, which is usually the neutral point of the power distribution system.

5. [Answer]: TN, TT and IT systems are the three grounding types in the low-voltage power distribution system respectively. In the TN system, the neutral point of the power supply is directly grounded, and the shell of the electrical equipment is connected to the connection point with a protection line. TN can be divided into three systems.

6. The neutral point of the power supply of the TN system is directly grounded, and there is a neutral line leading out. According to its protective line form, the TN system is divided into three types: TN-C system, TN-S system and TN-C-S system.

What does IT system refer to?

1, it refers to computers, communications and related technologies. Abbreviated as Information Technology. And the lowercase it refers to animals, plants and inanimate objects. Information technology (IT) in a broad sense is a general term for various technologies used to manage and process information.

2. The IT system is the right way to protect the zeroing system. It is a system in which the charged part of the power supply system is not grounded, or the exposed conductive part of the electrical equipment is grounded through impedance grounding.Nowadays, most of the grounding and zeroing systems adopt the standards stipulated by the International Electrotechnical Commission (IEC).

3. The IT system is the international standard IEC60364 that distinguishes three different types of grounding systems, and uses two letter codes to represent TN, TT and IT. The first letter indicates the relationship between the power supply end and the ground: T indicates that the power supply end is a little directly grounded; I means that all the charged parts of the power supply end are not grounded or a little grounded by impedance.

4. IT system, that is, the neutral point ungrounded system rnIT system: the power supply of the rn IT system is not grounded or grounded through impedance, and the exposed conductive part of the electrical equipment can be directly grounded or connected to the grounding body of the power supply through the protection wire, which is also a protective grounding.

it system belongs to

1, IT system is a low-voltage power distribution system, and "protection zero connection system" is only a one-sided statement. Definition of IT system: a system in which the neutral point of the power supply is not grounded, and the exposed conductive part of the electrical equipment is directly grounded. The IT system can have a neutral line, but IEC does not recommend setting a neutral line.

2. The IT system is the right way to protect the zeroing system. It is a system in which the charged part of the power supply system is not grounded, or the exposed conductive part of the electrical equipment is grounded through impedance grounding. Nowadays, most of the grounding and zeroing systems adopt the standards stipulated by the International Electrotechnical Commission (IEC).

3. The it system belongs to the risk management infrastructure, but the data is not. This statement is wrong. Data and IT systems are both the risk management infrastructure of banks.

4. TT system: the neutral point of the power supply is directly grounded, and the shell of the electrical equipment is grounded by their respective grounding devices. IT system: The neutral point of the power supply is not grounded or grounded by impedance, and the shell of the electrical equipment is grounded by its respective grounding devices.

5. The it system belongs to the risk management infrastructure, but the data is not. This statement is wrong. Data and IT systems are both the risk management infrastructure of banks.

Which of the following places can the it system be applied to

Protection grounding is suitable for all kinds of ungrounded distribution grids, such as some 1~10 kV distribution grids, low-voltage distribution grids under coal mines, etc. High requirements for power supply continuity, such as emergency power supply, hospital operating room, etc.Item B should use the TT system, and item CD should use the TN-C-S system.

It has been widely used in the fields of aircraft, automobiles, machinery, electronics, construction and light industry. For example, in the design process of electronic computers, CAD technology is used for architecture simulation, logic simulation, plug-in division, automatic wiring, etc., thus greatly improving the automation of design work.

It is generally used in places where power outages are not allowed, or in places where continuous power supply is strictly required, such as electric steelmaking, operating rooms in large hospitals, underground mines, etc. The power supply conditions in the underground mine are relatively poor, and the cables are susceptible to moisture.

The medical worker T system is a typical example of IT system application. Because of the special nature of its functions, the hospital has special requirements for its power distribution method.For example, surgical operating rooms, intensive care units, etc. need to adopt IT systems to provide a safe, reliable and continuous power distribution system.

What requirements should the globalized IT system take into account

1. Adhere to stability: the system software and hardware architecture should be scientific and reasonable, and the main system should adopt dual backup operation, and both software and hardware should be able to support 7× 24-hour stable operation requirements.

2. Data processing and management: IT systems can efficiently process, store and manage a large amount of data. This helps organizations better understand their business, customers and markets, so as to make wiser decisions. Automation and process optimization: IT systems can automate many tedious tasks, improve production efficiency and reduce human errors.

3. For security reasons, IT systems are often used in conjunction with leakage protection and zero break protection. IT system: three-phase three-wire power supply system, which is a protective grounding, and the power supply side is isolated from the ground. Or grounded by large impedance.

What is IT_What is it system

IT System (Information Technology System) refers to the composition of hardware, software, network and data, etc. The integrated system aims to support tasks such as information processing, data storage, analysis and communication.

IT system is a low-voltage power distribution system, and "protection zero connection system" is only a one-sided statement. Definition of IT system: a system in which the neutral point of the power supply is not grounded, and the exposed conductive part of the electrical equipment is directly grounded.The IT system can have a neutral line, but IEC does not recommend setting a neutral line.

IT system is an international standard IEC60364 that distinguishes three different types of grounding systems, using two letter codes to represent TN, TT and IT. The first letter indicates the relationship between the power supply end and the ground: T indicates that the power supply end is directly grounded; I indicates that all the energized parts of the power supply end are not grounded or a little grounded by impedance.

it system is a system in which the neutral point of the power supply is not grounded and the exposed conductive part of the electrical equipment is directly grounded; the tt system is a system in which the neutral point of the power supply and the exposed conductive part of the electrical equipment are directly grounded; the tn system is the neutral point of the power supply is directly grounded and the exposed conductive part of the electrical equipment and the power supply The system of direct electrical connection of the neutral point.

IT system is the right way to protect the zeroing system.It is a system in which the charged part of the power supply system is not grounded, or the exposed conductive part of the electrical equipment is grounded through impedance grounding. Nowadays, most of the grounding and zeroing systems adopt the standards stipulated by the International Electrotechnical Commission (IEC).