First: First of all, pay attention to whether the interface and elbow are leaking oil, and whether the sealing work is done well. Second: The use of engine oil will be more than before installing the oil cooling, because the oil cooling needs to store a certain amount of oil. When changing the oil, the oil in the oil cooling must be cleaned up.
Mineral oil and fully synthetic oil cannot be mixed. From a technical point of view, it is no problem to mix different types of engine oil. However, it should be noted that while mixing oil, you are also mixing the additives in them. It is not necessarily a good thing to mix the additives in different oils.
The oil cooling area is selected reasonably, the installation position is also reasonable, and the installation method must be correct.The specific oil cooling effect varies according to each machine, and the oil cooling measurement should be tested under the guidance of professionals.
For this reason, the following are a few issues that need to be paid attention to when using the engine in winter: add antifreeze. If the engine can start smoothly, it is best to use antifreeze as coolant. The quality of the selected antifreeze must be qualified, especially the pH and stability of the antifreeze must meet the requirements, otherwise it will corrode the waterway and water seal, causing water leakage and other faults.
1. It can't be changed. The cylinder head, cylinder block, engine whole box and many other parts of the air-cooled engine and water-cooled engine are completely different. The only way to change is to change the engine assembly, but it can be modified.Oil cooling, which is relatively easy, but it is difficult to say how much stronger the effect is than the current air cooling, and the effect is not very big.
2. When many drivers do maintenance in 4S stores, they will be persuaded by the staff to install oil cooling on the water-cooled engine. In fact, this is not necessary. Most cars on the market use three types of coolant, including ethylene glycol antifreeze, anhydrous antifreeze and cooling oil.
3. Water cooling: The water-cooled spindle is easy to rust, and the water source needs to be replaced frequently. The refrigeration method of the water cooler is only fan refrigeration, fan heat dissipation, and there is no refrigeration system itself.
4. Is LZ air-cooled to oil-cooled or water-cooled to oil-cooled? There is no need to change air cooling to oil cooling. Air cooling has met the requirements of heat dissipation. Water cooling to oil cooling is not good. The specific heat capacity of water and the specific heat capacity of oil are different. The temperature of oil generally rises faster, and the requirements for heat dissipation device are relatively high.
5. Hello, it's okay, but it's too expensive. Oil-cooled maintenance-free for life. [ If there is a problem with the car, ask the car master. 4S store professional technician, 10 minutes to solve.
Water-cooled motor is better. Smell and cost. In terms of cost. Large electric spindle water cooling canBy selecting high-quality coolants, such as special coolants for automobiles, it reduces the possibility of corrosion, and also increases the cooling effect to ensure that the spindle is working at the appropriate temperature. The discharge and treatment of wastewater are more environmentally friendly than oil products.
Water cooling is good. Nowadays, many models on the market adopt water-cooled engine cooling. Water cooling is to cool the engine with water. The purpose of cooling the engine through various tools. Therefore, its cooling method. It's relatively simple. The cooling effect is also relatively good, although the effect is relatively good.
In theory, oil cooling is better. Cooling time: Because the cooling speed of oil is slower than that of water, the cooling time of oil cooling is longer than that of water cooling. Hardness of quenching: high water cooling, low oil cooling. Chen quenching deformation: large water cooling, small oil cooling. The tendency of quenching cracking: large water cooling and small oil cooling.The depth of the quenching layer: deep water cooling, shallow oil cooling.
"The following is my personal opinion: Generally speaking, water cooling is better, the oil-cooled engine is easy to overheat, and the radiator is relatively large: the specific capacity of oil is too small, and water has the largest specific heat capacity in nature, that is, the water temperature rises by 1 degree and absorbs more heat than oil.
HS code verification for exporters-APP, download it now, new users will receive a novice gift pack.
First: First of all, pay attention to whether the interface and elbow are leaking oil, and whether the sealing work is done well. Second: The use of engine oil will be more than before installing the oil cooling, because the oil cooling needs to store a certain amount of oil. When changing the oil, the oil in the oil cooling must be cleaned up.
Mineral oil and fully synthetic oil cannot be mixed. From a technical point of view, it is no problem to mix different types of engine oil. However, it should be noted that while mixing oil, you are also mixing the additives in them. It is not necessarily a good thing to mix the additives in different oils.
The oil cooling area is selected reasonably, the installation position is also reasonable, and the installation method must be correct.The specific oil cooling effect varies according to each machine, and the oil cooling measurement should be tested under the guidance of professionals.
For this reason, the following are a few issues that need to be paid attention to when using the engine in winter: add antifreeze. If the engine can start smoothly, it is best to use antifreeze as coolant. The quality of the selected antifreeze must be qualified, especially the pH and stability of the antifreeze must meet the requirements, otherwise it will corrode the waterway and water seal, causing water leakage and other faults.
1. It can't be changed. The cylinder head, cylinder block, engine whole box and many other parts of the air-cooled engine and water-cooled engine are completely different. The only way to change is to change the engine assembly, but it can be modified.Oil cooling, which is relatively easy, but it is difficult to say how much stronger the effect is than the current air cooling, and the effect is not very big.
2. When many drivers do maintenance in 4S stores, they will be persuaded by the staff to install oil cooling on the water-cooled engine. In fact, this is not necessary. Most cars on the market use three types of coolant, including ethylene glycol antifreeze, anhydrous antifreeze and cooling oil.
3. Water cooling: The water-cooled spindle is easy to rust, and the water source needs to be replaced frequently. The refrigeration method of the water cooler is only fan refrigeration, fan heat dissipation, and there is no refrigeration system itself.
4. Is LZ air-cooled to oil-cooled or water-cooled to oil-cooled? There is no need to change air cooling to oil cooling. Air cooling has met the requirements of heat dissipation. Water cooling to oil cooling is not good. The specific heat capacity of water and the specific heat capacity of oil are different. The temperature of oil generally rises faster, and the requirements for heat dissipation device are relatively high.
5. Hello, it's okay, but it's too expensive. Oil-cooled maintenance-free for life. [ If there is a problem with the car, ask the car master. 4S store professional technician, 10 minutes to solve.
Water-cooled motor is better. Smell and cost. In terms of cost. Large electric spindle water cooling canBy selecting high-quality coolants, such as special coolants for automobiles, it reduces the possibility of corrosion, and also increases the cooling effect to ensure that the spindle is working at the appropriate temperature. The discharge and treatment of wastewater are more environmentally friendly than oil products.
Water cooling is good. Nowadays, many models on the market adopt water-cooled engine cooling. Water cooling is to cool the engine with water. The purpose of cooling the engine through various tools. Therefore, its cooling method. It's relatively simple. The cooling effect is also relatively good, although the effect is relatively good.
In theory, oil cooling is better. Cooling time: Because the cooling speed of oil is slower than that of water, the cooling time of oil cooling is longer than that of water cooling. Hardness of quenching: high water cooling, low oil cooling. Chen quenching deformation: large water cooling, small oil cooling. The tendency of quenching cracking: large water cooling and small oil cooling.The depth of the quenching layer: deep water cooling, shallow oil cooling.
"The following is my personal opinion: Generally speaking, water cooling is better, the oil-cooled engine is easy to overheat, and the radiator is relatively large: the specific capacity of oil is too small, and water has the largest specific heat capacity in nature, that is, the water temperature rises by 1 degree and absorbs more heat than oil.
HS code-based multi-country consolidation
author: 2024-12-23 21:07HS code-based alternative sourcing strategies
author: 2024-12-23 20:59Global trade certification services
author: 2024-12-23 19:45HS code-based global benchmarking
author: 2024-12-23 19:03HS code integration with audit trails
author: 2024-12-23 21:42How to simplify export documentation
author: 2024-12-23 21:22HS code mapping for re-importation
author: 2024-12-23 21:03How to access historical shipment records
author: 2024-12-23 20:25Integrated circuits HS code verification
author: 2024-12-23 19:45398.91MB
Check473.77MB
Check854.66MB
Check179.25MB
Check919.34MB
Check951.61MB
Check856.79MB
Check798.68MB
Check914.13MB
Check729.33MB
Check115.75MB
Check631.57MB
Check429.23MB
Check355.67MB
Check752.24MB
Check551.77MB
Check147.26MB
Check147.81MB
Check711.72MB
Check647.81MB
Check425.76MB
Check183.36MB
Check175.52MB
Check758.84MB
Check621.28MB
Check468.63MB
Check298.78MB
Check343.47MB
Check585.75MB
Check846.62MB
Check658.41MB
Check558.46MB
Check177.11MB
Check927.31MB
Check965.26MB
Check792.89MB
CheckScan to install
HS code verification for exporters to discover more
Netizen comments More
166 Commodity price indexing by HS code
2024-12-23 21:05 recommend
2513 How to reduce compliance-related delays
2024-12-23 20:57 recommend
1228 How to monitor competitor supply chains
2024-12-23 20:54 recommend
2682 HS code adaptation for local regulations
2024-12-23 20:50 recommend
1619 Dynamic import export data modeling
2024-12-23 19:59 recommend