The card reader is used to read the smart card information of the swiper ( Card number), and then convert it into an electrical signal and send it to the access control controller. According to the received card number, the controller judges through the software whether the cardholder has been authorized to enter the gate during this period of time, and completes the unlocking, maintaining the lock and other work according to the results of the judgment.
RealAt present, a variety of applications other than the access control system include electronic payment parking lot management, computer desktop login system, elevator operation and other applications. Through the open access control architecture, it realizes seamless upgrades and provides different upgrade options for the future.
There are several ways to solve the encrypted access control card: Replace the IC access control card: This is the simplest and most effective way to ensure the security of the access control system.
Enter the programming mode: press [*]+[6-bit programming password], beep twice, (the red light flashes, the green light is on. The factory programming password is 990101. Users must modify this programming password after enabling the access control device. If there is no programming instruction within 20 seconds, the system will automatically exit the programming state.
Expand content: except for the encryption gateCard ban, modern access control system can also support other security authentication methods, such as mobile phone Bluetooth door opening, QR code recognition, etc. The introduction of these technologies has further improved the convenience and security of the access control system.
According to the master key of the card issuing unit, the card issuing unit shall load the personal basic information files and application files of the unit, and print photos, names, etc. on the surface. In this way, the cards that have been personalized can be sent to the cardholder.
can be sent through the software to report the lost card The original function system of the elevator will automatically release the control of the elevator in the event of a power failure or system failure to restore the original function of the elevator.
You only need to bring your valid ID card to the account opening bank to report the loss directly. The bank staff will check the basic information according to the ID card number and find out the bank card number and other information.
Apply for loss at the customer service department of the IC card sales center. The procedures are as follows: A card: bring the original ID card or household registration book, pay a deposit of 18 yuan, and pick up the card with the loss report document three days later (A card without ID number cannot be reported lost).B card: bring the original ID card or household registration book, and go through the refund procedures with the loss report document three days later.
Bank of China. To report the loss verbally, you need to check the ID number, the name of the account opening bank, the account opening date and other information. When reporting the loss in writing, you need to bring your original ID card to fill in the application form for reporting the loss. China Merchants Bank. Orally report the loss by telephone, mobile banking, online banking or any branch of the bank, which is valid for 5 days.
1. Elevator IC card management system Intelligent IC card control elevator management system is controlled by IC cards installed in the elevator car and outside the hall.It consists of the instrument, the IC card issuance center installed in the management center, and the IC card held by the elevator users.
2. Security of the system. Elevator swipe card and IC card systems need to have a high degree of security to prevent illegal intrusion and malicious operations. When installing the system, it is necessary to carefully check all links of the system to ensure that it has a high degree of security and reliability. Privacy protection of users.
3. The intelligent IC card elevator elevator control system, that is, the IC card layer-controlled elevator control system, is the intelligent control system that takes over the original elevator system button through passive contacts. It is installed in the car. Only by using the IC card can you reach the floor you want to go to. You can swipe the card directly, no need to press the button, and the password to take the elevator.
4. Shenzhen Wanglong tells you about the principle and types of IC card elevators.: The intelligent IC card control elevator management system consists of the IC card controller installed in the elevator car and outside the hall, the IC card issuance center installed in the management center, and the IC card held by the elevator users.
The full name of the elevator control system is intelligent elevator IC card control system. The elevator control system is an IC card controller installed outside the elevator car and hall, installed in the management center. It is composed of IC cards held by users of IC card issuing centers and elevators.
What does the ladder control system mean? The so-called "ladder control" means that a device similar to "en access control" is installed on the original elevator. As long as you brush it once, it will automatically turn on and take the user to the floor you want to reach.
The ladder control system, also known as the intelligent elevator control system, is an intelligent management system that adopts advanced card reading and writing technology, automatic control technology and sensing technology, and uses the computer network platform to comprehensively automate the use of elevators.
Prospect photoelectric elevator IC card - economical configuration: main controller I smart card II main functions: 1 swipe the card to use the elevator; 2 shield idle personnel; 3 VIP floor control 4 convenient installation, fast debugging, convenient use.
The card reading module and the function expansion module constitute the elevator control unit. After the cardholder reads the card in the elevator, the system allows the cardholder to reach the authorized floor according to the prior settings. If the cardholder operates the unauthorized floor button, the elevator will not respond.Non-cardholders cannot operate the elevator.
The elevator IC card swipe system should be to control the use of the elevator (that is, it cannot be used by unrelated personnel, or it can be used for a fee), that is, it can only be used by swiping the elevator, and the installation method should have an installation instruction manual.
1. What does the escalator control system mean? The so-called "escalator control" means that a device similar to "enter control" is installed on the original elevator. As long as you brush it once, it will automatically turn on and Users take them to the floor they want to reach.
2. For the wiring principle of elevator card swipe and elevator IC card system, it generally needs to be operated according to the specific brand and model. It is recommended that you check the corresponding product manual and installation guide first.Generally speaking, the elevator swipe card and IC card system need to be connected with the elevator control system to realize the control and permission management of the elevator switch.
3. Elevator IC card controller is a high-tech product that takes IC and ID as information carriers and integrates information management, computer and smart card technology, which can control access and exit. It brings convenience to people's lives. It has a variety of functions of authorization, recording, query, statistics, anti-theft, alarm light, and has extremely high security capabilities.
4. The intelligent IC card elevator elevator control system, that is, the IC card layer-controlled elevator control system, is an intelligent control system that takes over the original elevator system button through passive contacts. It is installed in the car. Only by using the IC card can you reach the floor you want to go to. You can swipe the card directly without pressing the button, and the password to take the elevator.
5. The elevator IC card swipe system should be to control the use of the elevator (that is, it cannot be used by unrelated personnel, or it can be used for a fee), that is, the swipe card elevator can only be used, and the installation method should be installed using the installation manual.
6. Non-contact elevator IC card control system scheme Project introduction According to the actual situation and needs, the requirements of the whole project are as follows: (1) There are 2 office buildings and 10 elevators, which must be a ladder control system (swipe the card to the designated floor) (2) Equipped with 10 sets of ladder control systems (3) ladder The control system adopts the network mode.
1. The elevator IC card swipe system should be to control the use of the elevator (that is, it cannot be used by unrelated personnel, or it can be used for a fee), that is, it can only be used by swiping the elevator, and the installation method should have the installation instruction manual.
2. The installation method of the IC card elevator equipment of the ic card elevator is as follows: the ladder control and the elevator button signal line adopt the dry contact method, which does not change the original circuit of any elevator, and has no impact on the daily work of any brand elevator.
3. There are two installation methods for elevator IC cards: open installation and hidden installation. The open installation is simple, the installation cost is low and easy to operate. The disadvantage is that the prominent panel affects the beauty.
4. The wiring of different systems is different, and the wiring methods of layered control and unified control are also different, oftenThe wiring method shown is to string the output end of the card reader into the signal public end of the elevator button, and then set up the card reader. The setting method of card reader equipment of different manufacturers is different. Please refer to the random instruction manual.
5. Control method 1: Control the elevator call button outside the elevator. This control mode is to install a card reader outside the elevator, that is, at the elevator entrance of the elevator hall, and connect the elevator controller. When the user swipes the card effectively, the elevator summoning button can be activated, and the floor button in the elevator bridge box can be activated, and the user can use it. Elevator.
HS code-based negotiation with suppliers-APP, download it now, new users will receive a novice gift pack.
The card reader is used to read the smart card information of the swiper ( Card number), and then convert it into an electrical signal and send it to the access control controller. According to the received card number, the controller judges through the software whether the cardholder has been authorized to enter the gate during this period of time, and completes the unlocking, maintaining the lock and other work according to the results of the judgment.
RealAt present, a variety of applications other than the access control system include electronic payment parking lot management, computer desktop login system, elevator operation and other applications. Through the open access control architecture, it realizes seamless upgrades and provides different upgrade options for the future.
There are several ways to solve the encrypted access control card: Replace the IC access control card: This is the simplest and most effective way to ensure the security of the access control system.
Enter the programming mode: press [*]+[6-bit programming password], beep twice, (the red light flashes, the green light is on. The factory programming password is 990101. Users must modify this programming password after enabling the access control device. If there is no programming instruction within 20 seconds, the system will automatically exit the programming state.
Expand content: except for the encryption gateCard ban, modern access control system can also support other security authentication methods, such as mobile phone Bluetooth door opening, QR code recognition, etc. The introduction of these technologies has further improved the convenience and security of the access control system.
According to the master key of the card issuing unit, the card issuing unit shall load the personal basic information files and application files of the unit, and print photos, names, etc. on the surface. In this way, the cards that have been personalized can be sent to the cardholder.
can be sent through the software to report the lost card The original function system of the elevator will automatically release the control of the elevator in the event of a power failure or system failure to restore the original function of the elevator.
You only need to bring your valid ID card to the account opening bank to report the loss directly. The bank staff will check the basic information according to the ID card number and find out the bank card number and other information.
Apply for loss at the customer service department of the IC card sales center. The procedures are as follows: A card: bring the original ID card or household registration book, pay a deposit of 18 yuan, and pick up the card with the loss report document three days later (A card without ID number cannot be reported lost).B card: bring the original ID card or household registration book, and go through the refund procedures with the loss report document three days later.
Bank of China. To report the loss verbally, you need to check the ID number, the name of the account opening bank, the account opening date and other information. When reporting the loss in writing, you need to bring your original ID card to fill in the application form for reporting the loss. China Merchants Bank. Orally report the loss by telephone, mobile banking, online banking or any branch of the bank, which is valid for 5 days.
1. Elevator IC card management system Intelligent IC card control elevator management system is controlled by IC cards installed in the elevator car and outside the hall.It consists of the instrument, the IC card issuance center installed in the management center, and the IC card held by the elevator users.
2. Security of the system. Elevator swipe card and IC card systems need to have a high degree of security to prevent illegal intrusion and malicious operations. When installing the system, it is necessary to carefully check all links of the system to ensure that it has a high degree of security and reliability. Privacy protection of users.
3. The intelligent IC card elevator elevator control system, that is, the IC card layer-controlled elevator control system, is the intelligent control system that takes over the original elevator system button through passive contacts. It is installed in the car. Only by using the IC card can you reach the floor you want to go to. You can swipe the card directly, no need to press the button, and the password to take the elevator.
4. Shenzhen Wanglong tells you about the principle and types of IC card elevators.: The intelligent IC card control elevator management system consists of the IC card controller installed in the elevator car and outside the hall, the IC card issuance center installed in the management center, and the IC card held by the elevator users.
The full name of the elevator control system is intelligent elevator IC card control system. The elevator control system is an IC card controller installed outside the elevator car and hall, installed in the management center. It is composed of IC cards held by users of IC card issuing centers and elevators.
What does the ladder control system mean? The so-called "ladder control" means that a device similar to "en access control" is installed on the original elevator. As long as you brush it once, it will automatically turn on and take the user to the floor you want to reach.
The ladder control system, also known as the intelligent elevator control system, is an intelligent management system that adopts advanced card reading and writing technology, automatic control technology and sensing technology, and uses the computer network platform to comprehensively automate the use of elevators.
Prospect photoelectric elevator IC card - economical configuration: main controller I smart card II main functions: 1 swipe the card to use the elevator; 2 shield idle personnel; 3 VIP floor control 4 convenient installation, fast debugging, convenient use.
The card reading module and the function expansion module constitute the elevator control unit. After the cardholder reads the card in the elevator, the system allows the cardholder to reach the authorized floor according to the prior settings. If the cardholder operates the unauthorized floor button, the elevator will not respond.Non-cardholders cannot operate the elevator.
The elevator IC card swipe system should be to control the use of the elevator (that is, it cannot be used by unrelated personnel, or it can be used for a fee), that is, it can only be used by swiping the elevator, and the installation method should have an installation instruction manual.
1. What does the escalator control system mean? The so-called "escalator control" means that a device similar to "enter control" is installed on the original elevator. As long as you brush it once, it will automatically turn on and Users take them to the floor they want to reach.
2. For the wiring principle of elevator card swipe and elevator IC card system, it generally needs to be operated according to the specific brand and model. It is recommended that you check the corresponding product manual and installation guide first.Generally speaking, the elevator swipe card and IC card system need to be connected with the elevator control system to realize the control and permission management of the elevator switch.
3. Elevator IC card controller is a high-tech product that takes IC and ID as information carriers and integrates information management, computer and smart card technology, which can control access and exit. It brings convenience to people's lives. It has a variety of functions of authorization, recording, query, statistics, anti-theft, alarm light, and has extremely high security capabilities.
4. The intelligent IC card elevator elevator control system, that is, the IC card layer-controlled elevator control system, is an intelligent control system that takes over the original elevator system button through passive contacts. It is installed in the car. Only by using the IC card can you reach the floor you want to go to. You can swipe the card directly without pressing the button, and the password to take the elevator.
5. The elevator IC card swipe system should be to control the use of the elevator (that is, it cannot be used by unrelated personnel, or it can be used for a fee), that is, the swipe card elevator can only be used, and the installation method should be installed using the installation manual.
6. Non-contact elevator IC card control system scheme Project introduction According to the actual situation and needs, the requirements of the whole project are as follows: (1) There are 2 office buildings and 10 elevators, which must be a ladder control system (swipe the card to the designated floor) (2) Equipped with 10 sets of ladder control systems (3) ladder The control system adopts the network mode.
1. The elevator IC card swipe system should be to control the use of the elevator (that is, it cannot be used by unrelated personnel, or it can be used for a fee), that is, it can only be used by swiping the elevator, and the installation method should have the installation instruction manual.
2. The installation method of the IC card elevator equipment of the ic card elevator is as follows: the ladder control and the elevator button signal line adopt the dry contact method, which does not change the original circuit of any elevator, and has no impact on the daily work of any brand elevator.
3. There are two installation methods for elevator IC cards: open installation and hidden installation. The open installation is simple, the installation cost is low and easy to operate. The disadvantage is that the prominent panel affects the beauty.
4. The wiring of different systems is different, and the wiring methods of layered control and unified control are also different, oftenThe wiring method shown is to string the output end of the card reader into the signal public end of the elevator button, and then set up the card reader. The setting method of card reader equipment of different manufacturers is different. Please refer to the random instruction manual.
5. Control method 1: Control the elevator call button outside the elevator. This control mode is to install a card reader outside the elevator, that is, at the elevator entrance of the elevator hall, and connect the elevator controller. When the user swipes the card effectively, the elevator summoning button can be activated, and the floor button in the elevator bridge box can be activated, and the user can use it. Elevator.
Pharma R&D materials HS code verification
author: 2024-12-23 21:06Dairy products HS code verification
author: 2024-12-23 21:00Predictive analytics for trade flows
author: 2024-12-23 20:49Data-driven supplier diversity programs
author: 2024-12-23 20:40HS code applications in compliance software
author: 2024-12-23 19:13Asia trade corridors HS code mapping
author: 2024-12-23 20:53Supplier risk profiling with trade data
author: 2024-12-23 20:03Metals and alloys HS code verification
author: 2024-12-23 19:25Industrial spare parts HS code mapping
author: 2024-12-23 19:07How to improve vendor negotiations
author: 2024-12-23 18:39
How to improve vendor negotiations
626.17MB
Check
Trade flow analysis by HS code category
376.99MB
Check
Plant-based proteins HS code verification
921.59MB
Check
Global trade scenario planning
475.83MB
Check
Regional trade agreements HS code mapping
647.11MB
Check
Import risk analysis metrics
885.46MB
Check
Global trade reporting frameworks
169.93MB
Check
How to manage trade credit risks
985.53MB
Check
Industrial spare parts HS code mapping
838.62MB
Check
HS code-based market share analysis
119.99MB
Check
HS code mapping to logistics KPIs
986.17MB
Check
Top global trade data insights
687.57MB
Check
HS code alignment with trade strategies
322.18MB
Check
Trade data solutions for freight forwarders
441.69MB
Check
HS code trends in textiles and apparel
166.47MB
Check
Global trade KPI dashboard templates
757.36MB
Check
Real-time supply chain financing insights
358.55MB
Check
How to refine supply chain visibility
129.61MB
Check
Detailed trade data mapping tools
357.39MB
Check
HS code classification for electronics
796.92MB
Check
Container-level shipment data
547.45MB
Check
Global trade fair insights
846.22MB
Check
HS code compliance training modules
994.67MB
Check
Trade data integration with ERP systems
691.57MB
Check
Trade data-driven contract negotiations
397.85MB
Check
HS code-driven margin analysis
866.23MB
Check
How to utilize trade data in M&A
681.34MB
Check
How to adapt to shifting trade policies
261.37MB
Check
Country-of-origin rules by HS code
152.36MB
Check
Trade data-driven LCL/FCL strategies
385.72MB
Check
Trade data for chemical imports
867.93MB
Check
How to find HS code data for specific countries
844.86MB
Check
Pharmaceutical raw materials HS code checks
345.26MB
Check
HS code-based container load planning
181.85MB
Check
Supplier risk profiling with trade data
838.17MB
Check
Ready-to-eat meals HS code classification
766.14MB
Check
Scan to install
HS code-based negotiation with suppliers to discover more
Netizen comments More
2146 Apparel HS code mapping for global exports
2024-12-23 21:25 recommend
1937 Global trade data-driven asset utilization
2024-12-23 21:20 recommend
881 Dairy imports HS code references
2024-12-23 21:03 recommend
1547 HS code-driven customs risk scoring
2024-12-23 19:39 recommend
1231 Global tender participation by HS code
2024-12-23 18:40 recommend