Chemical industry HS code search

List of the catalog of this article:

• 1, How to open the cover
• 2, How to open the front cover of the car
• 3, How to open the hood of a car?
• 4、What is the reason for the car hood is not tight

How to open the cover

1. The hood switch is in the car and needs to be turned on manually. The position of the switch is around the pedal. There is a switch button on the left side of the pedal. We can press the switch to open the outer hood. Put the hydraulic cylinder of the hood into the groove of the hood to support it.

2. Open the door, sit in the driver's seat, and find the engine switch handle on the left side of the driver's seat; pull the car engine handle by hand when you hear a bang;There is an obvious gap in the engine hood; pull the safety buckle; pull the car support stick to put the top buckle on the hood.

3. Hand-pull switch Generally speaking, this kind of switch is in the lower left corner of the driver's seat. You only need to pull the switch up, and the front cover of the car will open, which is very simple. Button-type switch This kind of switch is generally on the panel on the left side of the central console. You only need to press the button, and the front cover will bounce up slightly.

4. The cover is opened. This car is relatively special, and you need to pay attention when opening it. When the engine cover is opened, it generally flips backwards, and a small part also needs to be flipped forward. The engine cover turned back is opened to a predetermined angle. It should not come into contact with the front windshield, and there should be a minimum spacing of about 10 mm.

How to open the front cover of the car

1. How to open the front cover of the car: Generally, there will be a handle at the bottom left of the driver's seat. After pulling, the front cover will bounce open a seam, and then put the palm of your right hand up. In the middle, there will be Lift the handle up and you can open it.

2. First, open the door, sit in the driver's seat, and then find the engine switch handle on the left side of the driver's seat. Pull the handle of the car engine with your hand when you hear a bang. Check whether the hood of the car engine is open. If there is already an obvious gap, it means that the hood of the car engine has been opened.

3. Hand-pull switch Generally speaking, this kind of switch is in the lower left corner of the driver's seat.You only need to pull the switch up, and the front cover of the car will open, which is very simple. Button-type switch This kind of switch is generally on the panel on the left side of the central console. You only need to press the button, and the front cover will bounce up slightly.

How to open the hood of a car?

The car mainly found the power switch on the hood.Generally, on the left panel of the driver's seat, it may be a power switch pulled by hand or foot. The owner can open the hood by pulling or stepping on the power switch with his hand. After the owner presses or steps on the power switch, the hood of the car will be lifted up, leaving a gap of about 3-5 centimeters.

First, open the door, sit in the driver's seat, and then find the engine switch handle on the left side of the driver's seat. Pull the handle of the car engine with your hand when you hear a bang. Check whether the hood of the car engine is open. If there is already an obvious gap, it means that the hood of the car engine has been opened.

Method: Turn on the hood switch first, then lift the hood, and finally hold the hood with the brace. The specific method is as follows: find the hood switch in the lower left corner of the cab, which is generally in these two positions in the figure.The hood will make a rattling sound when it is turned on. Lift the hood gently with your hands.

Specific steps: (1) First open the door, sit in the driver's seat, and then find the engine switch handle on the left side of the driver's seat. ( 2) Pull the handle of the car engine with your hand and hear a bang. ( 3) Check whether the hood of the car is open. If there is an obvious gap, it means that the hood of the car has been opened.

What's wrong with the rust on the edge of the soundproof cotton of the car cover

If there is this kind of rust on the edge of the cover, it is best to use a little baking soda and white vinegar, gently wipe it clean and then use anti-rust oil. In this way, the ideal effect can be achieved.

The temperature is high, go to a professional repair shop for repair.When the vv6 car engine runs, it will generate a very high temperature, and the sound insulation cotton is located inside the hood. The heat insulation effect will make it withstand a higher temperature. A long period of high temperature will cause the glue inside the sound insulation cotton to loosen and soften, and finally cause the sound insulation cotton to fall off.

After disassembling the interior panel, etc., check the interior of the car first. There are some unknown hidden dangers in some cars, such as water leakage in some parts, water accumulation and rust, etc. The brake line and some parts need to be lubricated, which can be done by the way.

Car soundproofing cotton is generally harmless: installing soundproofing cotton can reduce the noise generated by the engine, and the high temperature of the engine after installing soundproofing cotton also reduces the impact on the cabin cover, which can protect the paint and delay its aging.

Attach soundproof cotton and shock-absorbing glue in the carHowever, this method has a disadvantage, that is, in order to install these things, the door panel must be disassembled and installed, which will lead to the problem of abnormal noise in the later stage.

What is the reason why the hood of the car hood is not tight

1. It may be that the vehicle hood is blocked by foreign objects and cannot be closed tightly. The owner needs to reopen the hood of the vehicle and take out the foreign object between the hood and the engine. Then close the engine hood correctly. It may be that the owner closes the hood of the vehicle incorrect way, resulting in the pull wire of the hood not returning to position and the hood lock being deformed.

2. [Pacific Automobile Network] The cover wire does not return, and the cover lock is deformed; the lock machine is loose, causing the lock machine to fall; the lock machine shifts, the lock hook breaks, etc.; it is recommended to go immediatelyThe auto repair shop has been appraised and repaired. The speed should not be too fast before it is repaired, which may cause an accident due to the wind resistance cover flying to the front glass.

3. The installation of the water tank assembly is not firm after replacement: If the water tank assembly is not fully installed in place or the installation is unstable after replacement, the hood may not be able to close normally. Check whether the water tank assembly is properly installed and firmly fixed.

4. The crv engine hood is not tight because the vehicle hood is blocked by foreign objects. Open the hood of the vehicle again, take out the foreign object between the hood and the engine, and then close the engine hood correctly.