Hello, reading the fault code 1215, which means that the air flow meter or its line is poor. After testing, the impedance of the air flowmeter does not meet the requirements. After replacing the air flowmeter, the condition of the car improved slightly, but the fault was still there. Check again and find that the 4th cylinder spark plug is covered with gasoline, indicating that the cylinder is not working.
The engine has serious carbon accumulation. The most common cause of idling jitter is excessive carbonisation of the throttle valve or fuel nozzle.
The solutions to unstable idle speed, shaking, shaking and black smoke are as follows: the engine is seriously carbonized. The common cause of car shaking is that the throttle valve is too dirty or the fuel nozzle has too much carbon.Solution: Clean the oil road and check whether there is carbon in the idle motor, which should be cleaned.
The control unit receives the wrong signal and sends the wrong instruction, causing the engine idling intake control to be inaccurate, causing the engine to burn abnormally, which is an indirect cause of unstable idle speed. Common causes are: air flow meter or its line failure; intake pressure sensor or its line failure; engine control unit plug due to poor contact with water inlet or internal computer failure.
Engine ignition order is 2; that is to say, when cylinder 1 is doing work, cylinder 3 is in a compressed state, cylinder 4 is in the intake state, and cylinder 2 is in the exhaust state. Status.
People sit in the cab, and the order of the cylinder is: 5 on the right, and 6 on the left.In this case, the ignition order is: 1-4-5-2-3-6.
The ignition order of the engine is 2; that is, when the 1st cylinder is in the "work", the 3rd cylinder is in the "compression" state, the 4th cylinder is in the "ink-ink" state, and the 2nd cylinder is in the "exhaust" state. Depending on the number of engine cylinders, the ignition order of the engine will also vary.
Engine carbon accumulation problem, the engine will accumulate some carbon accumulation after a period of use, which will cause engine damage, difficulty in starting, poor acceleration, starting The machine is too noisy and other phenomena. Mixed gas combustion is poor and gas combustion is insufficient. Sensor problem. Multiple sensors are aging. If the owner does not add oil as required, it will lead to accelerated engine wear and abnormal operation in the long run, and the engine fault light will turn on. Generally, replacing the oil with the corresponding conditions can eliminate the fault light. The reasons why the engine fault light is on are engine carbonisation problems, poor combustion of mixed gas, sensor problems, maintenance problems and oil quality problems.Car owners need to regularly clean the carbon accumulation of the engine, check the working condition of the sensor, maintain it regularly, and use qualified oil products. The fuel quality is poor and does not meet the standard.
Predictive supply chain resilience-APP, download it now, new users will receive a novice gift pack.
Hello, reading the fault code 1215, which means that the air flow meter or its line is poor. After testing, the impedance of the air flowmeter does not meet the requirements. After replacing the air flowmeter, the condition of the car improved slightly, but the fault was still there. Check again and find that the 4th cylinder spark plug is covered with gasoline, indicating that the cylinder is not working.
The engine has serious carbon accumulation. The most common cause of idling jitter is excessive carbonisation of the throttle valve or fuel nozzle.
The solutions to unstable idle speed, shaking, shaking and black smoke are as follows: the engine is seriously carbonized. The common cause of car shaking is that the throttle valve is too dirty or the fuel nozzle has too much carbon.Solution: Clean the oil road and check whether there is carbon in the idle motor, which should be cleaned.
The control unit receives the wrong signal and sends the wrong instruction, causing the engine idling intake control to be inaccurate, causing the engine to burn abnormally, which is an indirect cause of unstable idle speed. Common causes are: air flow meter or its line failure; intake pressure sensor or its line failure; engine control unit plug due to poor contact with water inlet or internal computer failure.
Engine ignition order is 2; that is to say, when cylinder 1 is doing work, cylinder 3 is in a compressed state, cylinder 4 is in the intake state, and cylinder 2 is in the exhaust state. Status.
People sit in the cab, and the order of the cylinder is: 5 on the right, and 6 on the left.In this case, the ignition order is: 1-4-5-2-3-6.
The ignition order of the engine is 2; that is, when the 1st cylinder is in the "work", the 3rd cylinder is in the "compression" state, the 4th cylinder is in the "ink-ink" state, and the 2nd cylinder is in the "exhaust" state. Depending on the number of engine cylinders, the ignition order of the engine will also vary.
Engine carbon accumulation problem, the engine will accumulate some carbon accumulation after a period of use, which will cause engine damage, difficulty in starting, poor acceleration, starting The machine is too noisy and other phenomena. Mixed gas combustion is poor and gas combustion is insufficient. Sensor problem. Multiple sensors are aging. If the owner does not add oil as required, it will lead to accelerated engine wear and abnormal operation in the long run, and the engine fault light will turn on. Generally, replacing the oil with the corresponding conditions can eliminate the fault light. The reasons why the engine fault light is on are engine carbonisation problems, poor combustion of mixed gas, sensor problems, maintenance problems and oil quality problems.Car owners need to regularly clean the carbon accumulation of the engine, check the working condition of the sensor, maintain it regularly, and use qualified oil products. The fuel quality is poor and does not meet the standard.
How to interpret bill of lading data
author: 2024-12-23 21:08Timber (HS code ) import patterns
author: 2024-12-23 20:14How to use analytics for HS classification
author: 2024-12-23 19:38Import data trends visualization
author: 2024-12-23 19:29Real-time supply-demand matching
author: 2024-12-23 19:12How to access historical shipment records
author: 2024-12-23 20:39HS code-based global trend analysis
author: 2024-12-23 20:08Data-driven customs paperwork reduction
author: 2024-12-23 20:00How to find untapped export partners
author: 2024-12-23 19:13Global HS code data enrichment services
author: 2024-12-23 19:11287.45MB
Check663.62MB
Check544.13MB
Check893.66MB
Check997.96MB
Check461.91MB
Check746.31MB
Check631.63MB
Check765.66MB
Check821.72MB
Check133.61MB
Check781.85MB
Check166.41MB
Check965.16MB
Check776.67MB
Check876.51MB
Check381.42MB
Check188.41MB
Check169.62MB
Check144.63MB
Check571.15MB
Check392.59MB
Check428.22MB
Check697.88MB
Check965.22MB
Check511.56MB
Check627.24MB
Check659.14MB
Check215.19MB
Check136.89MB
Check697.34MB
Check394.15MB
Check871.67MB
Check176.85MB
Check891.55MB
Check221.38MB
CheckScan to install
Predictive supply chain resilience to discover more
Netizen comments More
232 Advanced HS code product classification
2024-12-23 21:19 recommend
2159 Trade compliance automation tools
2024-12-23 20:54 recommend
1027 USA export trends analytics
2024-12-23 20:00 recommend
275 Global logistics analytics platforms
2024-12-23 19:27 recommend
1775 End-to-end shipment tracking solutions
2024-12-23 19:14 recommend