Advanced trade route cost analysis

List of the catalog of this article:

• 1,Advanced trade route cost analysis How to install the car seat cushion
• 2,< A href='#How to install a car all-enclosed cushion' title='How to install a car all-enclosed cushion'>How to install the car full-enclosed cushion
• 3, How to install the summer seat cushion

How to install the car seat cushion

1. Usually, a set of car cushions includes: two front driver's seats, two single backrests and one long cushion in the rear seat, a total of five Piece.

2. Install the car cushion. The specific steps are as follows: First, take out the new car cushion and check it, as shown in the figure below. Next, put in the cushion vest, as shown in the figure below.Then, put on the seat cushion head cover, as shown in the figure below. Next, take out the cuck, as shown in the figure below.

3. Take out the car cushion in the front row, put in the cushion vest, cover the cushion head cover, take out the chuck, and install the chuck. Insert the cuck into the gap, plug it into the cuck and then jam it, fasten the cuck, adjust the cushion apron, fasten the elastic band of the car cushion apron, and put it into the car cushion headrest.

4. Method Step 1: First, check whether all aspects of the car cushion are not damaged and whether the number of pieces is complete. Generally, car cushions include two front-driver seats, two single backrests and one long cushion, a total of five pieces.

5. First, connect the chuck to the elastic band, just pass the elastic band through the chuck. Then insert the slot into the seat gap and pull the chuck out from the back of the seat.Link the elastic band to the metal hook, as shown in the figure below.

6. Move the seat. To install the car cushion, you first need to move the front seat back. After moving back, take out the chuck hook and put it on the cushion. The chuck goes through the middle gap of the seat to the back to get stuck. The hook below is the suitable position under the seat.

How to install the car all-enclosed cushion

1. All-inclusive cushion cover installation method: First, the backrest cover is directly installed into the backrest, and adjust the seat cover to match the seat curve. Then pull the velvet cloth at the bottom of the backrest cover through the gap between the seat backrest and the cushion to the back, and pull it hard from behind to make the seat cover fit tightly.

2. Take out the car cushion in the front row, put it on the cushion vest, put on the cushion head cover, take out the chuck, and install the chuck.Put the cuck into the gap, put it in the cuck and get stuck, put it in the cuck, adjust the cushion apron, put the elastic band of the car cushion apron, and put it into the car cushion headrest.

3. Install the car cushion. The specific steps are as follows: First, take out the new car cushion and check it, as shown in the figure below. Next, put in the cushion vest, as shown in the figure below. Then, put on the seat cushion head cover, as shown in the figure below. Next, take out the cuck, as shown in the figure below.

How to install the summer cushion

1. Take out the front-row car cushion, put it in the cushion vest, put on the cushion head cover, take out the chuck, and install the chuck. Put the cuck into the gap, put it in the cuck and get stuck, put it in the cuck, adjust the cushion apron, put the elastic band of the car cushion apron, and put it into the car cushion headrest.

2. Move the seat. To install the car cushion, you first need to move the front seat back. After moving back, take out the chuck hook and put it on the cushion. The chuck goes through the middle gap of the seat to the back to get stuck. The hook below is the suitable position under the seat.

3. Install the front row first.Tile the driver's seat (co-driver) with the cushion. 04 First, use an elastic lock to fix the headrest cover. 05 Fix the cushion on the back of the chair with leather straps and buckles, and then fix the root of the cushion with the chuck. 06 Fix the hem of the cushion to the seat base with the card hook.

4. First, remove the rear cushion. Generally, the rear cushion is fixed by a snap. Lift one side first, and then lift it all. If the cushion can't be used, you can put it into the snap with a cone and pry it. After removing the cushion, put on the seat cover, turn the cushion over, and connect the elastic bands on both sides of the seat cover with the chuck.

5. Pull out the headrest first (generally hold down the headrest moving plug). Cover the backrest cover (see the left, right and front and back) well; distinguish between left and right depends on whether the backrest side bag is in the middle. If it is on the side of the door, it means that it is installed in reverse.

6. First, connect the chuck to the elastic band, just pass the elastic band through the chuck. Then insert the slot into the seat gap and pull the chuck out from the back of the seat. Link the elastic band to the metal hook, as shown in the figure below.